Click for
Table of Contents

menuUWB-XG Quick Start Guide

Package Contents

UniFi WiFi BaseStation XG
Adjustment Bracket
Pole Clamp
Carriage Bolts (Qty. 4)
Flange Nuts (Qty. 4)
Lag Screws (Qty. 4)
Gigabit PoE (50V, 1.2A)
Power Cord

Installation Requirements

IMPORTANT: The UWB-XG requires the UniFi Network Application v5.7 or higher, available at:

Outdoor Installation Requirements

System Requirements

Hardware Overview



10 GbE

The 10 GbE port is a 1/10 Gbps Ethernet port used to connect to the LAN and DHCP server. It can also be used to connect the power.

Note: The UWB-XG can be powered using an 802.3bt PoE switch or the included Gigabit PoE adapter. For instructions, see Connecting Power.

1 GbE

The 1 GbE port is a 10/100/1000 Ethernet port used for bridging. It can also be used to connect the power.


The Reset button serves two functions for the UWB-XG:

  • Restart Press and release the Reset button quickly.
  • Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.

VESA Mounting

If you choose to use your own mount, remove the four M4 x 10 screws from the back of the UWB-XG and detach the pre-installed mount.

Hardware Installation

Pole Mount

  1. Proceed to Connecting Ethernet.

Wall Mount

To mount the UWB-XG on a wall or other sturdy flat surface, securely attach the Adjustment Bracket to the wall using the four Lag Screws.

Note: The Adjustment Bracket must attach to a hard surface or other stable structure.

  1. Proceed to Connecting Ethernet.

Connecting Ethernet

Note: If you are using TOUGHCable, we recommend attaching the TOUGHCable Connector(s) after you insert the cable(s) into the cable gland(s).

The cable gland is comprised of the following components:

  1. Repeat steps 1-14 to connect an Ethernet cable to the 1 GbE port if one of the following conditions applies:
    • You will use the 1 GbE port for bridging.
    • You will use the 1 GbE port for 802.3bt PoE.
    • You will use the included Gigabit PoE adapter to power the UWB-XG.

Note: By default, the UWB-XG is set to 15 dBi for its small-cell gain. To switch to its large-cell gain of 10 dBi, use the UniFi Network Application.

Connecting Power

IMPORTANT: Using the 10GbE port requires enabling flow control on the upstream switch port’s configuration for maximum performance.





(without Mount)

471.1 x 257.5 x 94.3 mm

(18.55 x 10.14 x 3.713")


(without Mount)


3.2 kg (7.055 lb)

Networking Interface

(1) 10/100/1000 RJ45 Ethernet Port

(1) 1/10 Gbps ICM Ethernet Port




RGB, Application-Controllable

Power Method

802.3bt PoE

Power Supply

50VDC, 1.2A Gigabit PoE

Max. Power Consumption


Supported Voltage Range


Max. TX Power

25 dBm


(3) 4 x 4

Operating Frequency

5 GHz


Integrated Dual-Mode Antenna Array

Antenna Gain


Small Cell 15 dBi
Large Cell 10 dBi

Antenna Beamwidth


Small Cell 50°
Large Cell 90°

Wi-Fi Standards

802.11 a/n/ac/ac-wave2

Wireless Security

WPA-Enterprise (WPA/WPA2, TKIP/AES)


VESA-Compatible Mount

Pole/Wall (Brackets Included)

Operating Temperature

-40 to 70° C (-40 to 158° F)

Operating Humidity

5 to 95% Noncondensing