Package Contents
![]() |
---|
UDM |
![]() |
---|
AC Power Cord |
System Requirement
Either of the following is required:
- iOS or Android™ Mobile Device with UniFi Network Mobile App Installed
- Web Browser: Google Chrome (Other browsers may have limited functionality)
IMPORTANT: We strongly recommend using UPS backup and power regulation to prevent equipment damage due to stability issues with local AC power. |
Hardware Overview
![]() System LED |
|
---|---|
White |
Device is ready to be configured |
Flashing White |
Device is booting up Device is initializing/deinitializing |
Heartbeat White |
Firmware update in process |
Blue |
Device is configured and ready |
Slow Flashing Blue |
Client connected to device via Bluetooth (BLE) |
Flashing Off/White/Blue |
Device is in recovery mode. The LED will cycle through a pattern at one-second intervals, between off, white, and blue. |
![]() LAN (Ports 1-4) |
|
RJ45 switch ports support 10/100/1000 Ethernet connections for the LAN (Local Area Network). By default, they are set to DHCP Server with the fallback IP address, 192.168.1.1/24. |
|
![]() Internet Port |
|
The RJ45 port supports a 10/100/1000 Ethernet connection. Set to DHCP Client by default. |
|
![]() Power Port |
|
Connect the included AC Power Cord. |
|
![]() Reset Button |
|
Resets to factory defaults. The device should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the System LED becomes solidly lit light blue. After a few seconds, the LED will turn off, and the device will automatically reboot. |
Installation Requirements
Use Category 5 (or above) UTP cabling approved for indoor use.
Hardware Installation
|
Note: You can use Bluetooth on your smartphone to set up the device. |
---|
Configuration
You have the following options:
- Enable Bluetooth on your mobile device and use the UniFi Network Mobile app.
- Enable Wi-Fi on your mobile device and connect to UDM Setup <XXXX> (XXXX is the last four characters of the device’s MAC address found on the bottom device label). Go to “Chrome Instructions”.
- Use a computer connected to the device on any LAN port, 1-4. Go to “Chrome Instructions”.
UniFi Network Mobile App
Chrome Instructions
Use the Chrome web browser to set up your device.
- Ensure that your host system is on the same Layer 2 network as the UDM.
- Launch the Chrome web browser and go to https://setup.ui.com
- Follow the on-screen instructions of the Setup Wizard.
You can manage your network and view network statistics using the UniFi Network Application interface. For information on using the UniFi Network Application, refer to the User Guide located on our website at: ui.com/download/unifi
Specifications
UDM |
|
Dimensions |
ø110 x184.2 mm (ø4.33 x 7.25") |
---|---|
Weight |
1.05 kg (2.32 lb) |
Networking Interfaces |
(4) 10/100/1000 RJ45 Ports |
Max. Power Consumption |
26W |
Power Method |
AC Power Cord |
Power Supply |
Internal AC/DC Power Adapter, |
Supported Voltage Range |
100 - 240VAC |
LED |
System Status |
Operating Frequency |
2.4 GHz 5 GHz |
Max. TX Power |
|
2.4 GHz | 23 dBm |
5 GHz | 30 dBm |
Antenna |
(1) Dual-Band, Quad-Polarity Antenna |
Antenna Gain |
|
2.4 GHz | 3 dBi |
5 GHz | 4.5 dBi |
Wi-Fi Standards |
802.11 a/b/g/n/ac/ac-wave2 |
Wireless Security |
WEP, WPA-PSK, |
Operating Temperature |
-10 to 45° C (14 to 113° F) |
Operating Humidity |
5 to 95% Noncondensing |
Certifications |
CE, FCC, IC |