Package Contents


Camera


Tightening Tool


Pole Mount Bracket


Screw Anchors (Qty. 2)


Self-Tapping Screws (Qty. 2)


Machine Screws (Qty. 2)

Installation Requirements

Pole-mounting: Two metal straps (not included)
Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the camera and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.

Ethernet Port
10/100/1000 RJ45 port connects to an 802.3af/802.3at switch for PoE power and data.
Reset Button
The Reset button serves two functions: Reboot Press and release the Reset button quickly. Restore to Factory Defaults Press and hold the Reset button for 10-20 seconds while the camera is powered on.
Cable Gland
Creates a tight seal around the Ethernet cable to prevent water from damaging the RJ-45 port.
LED Ring
White	Ready for configuration.
Flashing White	Initializing.
Heartbeat Flashing White	Device is being reset to factory defaults.
Blue	Indicates the device has been successfully adopted into a network and is working properly.
Rotating Blue	Motion detected.
Alternating White/Blue	Firmware upgrade in progress. Device is busy; do not touch or unplug it.
Repeating Off/White/Blue	Recovery mode.
Flashing Red	Recording.
Red	Device failure; network error. If this occurs, we recommend rebooting the device.

Remove the sticker from the bottom of the Mounting Base.

To install the camera, please follow the instructions of the following sections in this order:

The camera can be mounted on a wall, ceiling, or pole. Follow the appropriate steps for your installation:

	IMPORTANT: If you are installing your camera outdoors, create a drip loop for the cable below the camera to prevent water ingress.

	IMPORTANT: For proper weather sealing, the Cable Gland must fit securely within the Adjustable Base when the camera is mounted. Ensure that the Cable Gland is securely seated during installation and cable routing.

	Note: When you first launch UniFi Protect, the app will prompt you to enable Bluetooth and other features necessary to provide the best user experience possible. Please allow these features and permissions for proper app functionality.

UVC-G4-PRO
Dimensions	Ø 86 x 153 mm (Ø 3.39 x 6.02") (Without Mounting Plate)
Weight	700 g (1.54 lb) (Without Mounting Plate)
Enclosure	PC/TPE/Aluminum Alloy (ADC-12 + Liquid Coating)
Networking Interface	(1) 10/100/1000 Ethernet Port
Sensor	OS08A10, 1/2"
Lens	F 4.1mm - 12.3mm; f/1.53 -f/3.3
LED	LED Ring
Field of View
Wide	108° (H), 58° (V), 125° (D)
Tele	37° (H), 20° (V), 43° (D)
Night Mode	IR LEDs with Mechanical IR Cut Filter
Video Compression	H.264
Resolution	4K2K (3840 x 2160)
Max. Frame Rate	30 FPS
Image Settings	Flip, Brightness, Contrast, WDR, Hue, Infrared, Sharpness, Saturation, Denoise, 50/60 Hz Flicker Reduction
Management Interface
Managed Mode	UniFi Protect
Standalone Mode	Camera Integrated Web UI
Microphone	Yes
Max. Power Consumption	12.5W
Power Method	IEEE 802.3af/at
Power Supply	802.3af/802.3at or UniFi PoE Switch
Buttons	Factory Reset Button
Mounting	Wall, Ceiling, Pole (Kits Included)
Operating Temperature	-20 to 50° C (-4 to 122° F)
Operating Humidity	0 to 90% Noncondensing
Weatherproofing	IP67