Package Contents
![]() |
---|
UFiber UF-WIFI |
![]() |
---|
Screws (Qty. 4) |
![]() |
---|
Screw Anchors (Qty. 4) |
![]() |
---|
Power Adapter (24V, 0.5A) |
System Requirements
- Linux, Mac OS X, or Microsoft Windows 7/8/10
- Web Browser: Google Chrome (Other browsers may have limited functionality)
Before You Begin
Designing your first GPON deployment requires specific knowledge and planning. For information on GPON network design and installation, including important considerations and best practices, refer to:
For details on configuring UFiber devices for the first time to allow ONU LAN ports to provide connectivity, refer to: ubnt.link/UFiber-Initial-Configuration
Hardware Overview
![]() PON Port |
|
---|---|
SC/APC GPON port supports WAN connections of 2.488 Gbps downstream and 1.244 Gbps upstream. |
|
![]() LAN (Ports 1 - 4) |
|
RJ45 Ethernet LAN ports support 10/100/1000 Mbps connections. Port 1 also supports 24V Passive PoE to power the device. |
|
![]() Reset Button |
|
The Reset button serves two functions for the UF-WIFI:
|
|
![]() Power Port |
|
The Power Adapter connects to this port to provide power. |
|
White |
Ethernet connection up |
![]() Signal LEDs |
|
Off |
Bootup |
Signal strength: low ≥ -28 dBm |
|
Signal strength: good ≥ -25 dBm |
|
Signal strength: strong ≥ -11 dBm |
|
Signal strength: too low < -28 dBm Check the quality of the fiber connection, and calculate the total optical loss of the optical splitters. |
|
Signal strength: too strong ≥ -8 dBm Add an optical splitter, or add a 5 or 10 dB optical attenuator. |
|
No signal Check the fiber cables and connectors, and ensure that the OLT functions properly. |
|
No authority The UF-WIFI has not been authorized or cannot communicate with the OLT. Check passwords and OLT settings. |
|
![]() Ethernet LED |
|
Off |
Ethernet connection down |
White |
Ethernet connection up Flashing indicates activity |
![]() Power LED |
|
Off |
Power off |
White |
Power on |
Hardware Installation
Wall Mounting
Connecting Fiber
|
WARNING: Never look directly into the ends of fiber or modules. The emitted light could cause damage to the eye. |
---|
|
WARNING: Until ready for use, keep modules and fiber patch cables covered using the included protective caps to ensure the connections stay clean. |
---|
|
WARNING: Do NOT connect the device directly to a UFiber GPON module (UF-GP-B+ or UF-GP-C+). Doing so will damage the device optics. Ensure that the device’s received signal level never exceeds -8 dBm. Use a UFiber PLC Splitter to add attenuation as needed. |
---|
Connecting LAN
Connecting Power
OR
|
Note: 24V Passive PoE is required to power the device. |
---|
|
WARNING: The PoE switch must comply with the power specifications listed in the Specifications section of this Quick Start Guide. |
---|
Accessing the Configuration Interface
- Ensure that your computer (or other host system) is connected to the device.
- Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
- Launch your web browser. Type http://192.168.1.1 in the address field. Press enter (PC) or return (Mac).
- Enter ubnt in the Username and Password fields. Click Login.
Customize settings as needed. For more information, refer to the UFiber resources, which are available at: http://ubnt.link/UFiber-Support
Specifications
UF-WIFI |
|
Dimensions |
126.34 x 126.09 x 31.65 mm |
---|---|
Weight |
190 g (6.70 oz) |
Networking Interfaces |
(1) SC/APC, GPON WAN (4) Gigabit RJ45, Ethernet LAN (1) Wi-Fi, 802.11n |
Networking Interface Speeds |
|
GPON WAN, ITU G.984 | 2.4 Gbps Down, 1.2 Gbps Up |
LAN | 10/100/1000 Mbps |
Wi-Fi | 300 Mbps |
Management Interface |
In-Band Ethernet PON |
Normal Optical Power Range |
TX (Class B+): 1.5 to 5 dBm RX: -28 to -8 dBm |
Power Method |
DC Jack, 24VDC 24V Passive PoE (Pins 4, 5+; 7, 8-) |
Power Supply |
100-240VAC / 50-60 Hz Universal AC/DC |
Max. Power Consumption |
7W |
Supported Voltage Range |
20 to 28V |
Processor Specs |
MIPS, 900 MHz |
Memory Information |
256 MB DDR |
Button |
(1) Reset |
Operating Temperature |
-10 to 45° C (14 to 113° F) |
Operating Humidity |
10 to 90% Noncondensing |
Certifications |
CE, FCC, IC |