Package Contents

* Included only in the single-pack of the UAP-FlexHD

Installation Requirements

• Phillips screwdriver
• Cat5/6 UTP cable for indoor installations
• Shielded Category 5 (or above) cabling should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.

System Requirements

• UniFi Cloud Key or Dream Machine, or machine running Linux, Mac OS X, or Windows 7/8/10
• Java Runtime Environment 1.8 or above recommended
• Web Browser: Google Chrome (Other browsers may have limited functionality.)
• UniFi Network Application v5.11.31 or newer (available at: ui.com/download/unifi)

Hardware Overview

LED
White	Factory default, waiting to be integrated.
Flashing White	Initializing.
Alternating White/Blue	Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place.
Blue	Indicates the device has been successfully integrated into a network and is working properly.
Quickly Flashing Blue	This is used to locate an AP. When you click Locate in the UniFi Network Application, the AP will flash. It will also display the location of the AP on the map.
Steady Blue with Occasional Flashing	Indicates the device is in an isolated state (all WLANs are brought down until an uplink is found).
Ethernet Port
This Gigabit Ethernet port is used to connect 802.3af PoE power and should be connected to the LAN and DHCP server.
Reset Button
The Reset button serves two functions for the UniFi AP: Restart Press and release the Reset button quickly. Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.

Installation

Determine the installation location of the UAP FlexHD:

• Desktop The UAP FlexHD stands freely on a horizontal surface such as a desktop or table/shelf. Good for temporary installations.
• Wall The UAP FlexHD is attached to a wall in a secure location.
• Ceiling The UAP FlexHD is mounted in a ceiling tile (requires optional recessed ceiling mount assembly, sold separately).
• Pole The UAP FlexHD is attached to a pole (indoor or outdoor).

	Note: When installing Ethernet cabling on a pole or up the outer surface of a wall, use RJ45 connectors without strain-relief boots on them. This will prevent unnecessary tension on the cable ends.

Cable without a strain-relief boot	Cable with a strain-relief boot

Proceed to the appropriate section for your installation.

Desktop

1. 

2. 

3. 

4. 

Wall

1. 

2. 

3. 

4. 

5. 

Ceiling (Optional Accessory)

Use the optional Ceiling Mount, Mount Cover, and Back Plate Assembly to install the UAP FlexHD on a drop tile ceiling or horizontal surface where the interior side of the Ceiling Mount is accessible.

1. 

2. 

3. 

4. 

Pole

	Note: If you are mounting the UAP-FlexHD outdoors, it must be installed in the upright position to prevent water from getting into the base of the device.

1. 

2. 

3. 

4. 

5. 

6. 

Connecting Power

OR

Specifications

UAP-FlexHD
Dimensions	Ø 48.50 x 159.49 mm (1.90 x 6.28")
Weight	315 g (0.69 lb)
Networking Interface	(1) 10/100/1000 Ethernet Port
Button	Reset
LED	System
Power Method	802.3af PoE
Power Supply	802.3af PoE 48V, 0.32A Gigabit PoE Adapter
Max. Power Consumption	10.5W
Supported Voltage Range	44 - 57VDC
Operating Frequency	2.4 GHz 5 GHz
Max. TX Power
2.4 GHz	23 dBm
5 GHz	26 dBm
Throughput
2.4 GHz	300 Mbps
5 GHz	1733 Mbps
Antenna Gain
2.4 GHz	1.6 dBi
5 GHz	4 dBi
Wi-Fi Standards	802.11 a/b/g/n/ac/ac-wave2
Wireless Security	WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES)
Mounting	Desktop/Wall/Ceiling/Pole
Operating Temperature	-30 to 70° C (-22 to 158° F)
Operating Humidity	5 to 95% Noncondensing
Certifications	CE, FCC, IC