×

Click for
Table of Contents

menuES-24-Lite Quick Start Guide

Package Contents

EdgeSwitch Lite
Rack-Mount Brackets (Qty. 2)
Bracket Screws (Qty. 8)
Mounting Screws (Qty. 4)
Cage Nuts (Qty. 4)
Power Cord

Installation Requirements

Hardware Overview

Front Panel LEDs

System LED

Note: The System LED functionality has been updated with firmware v1.8.0. We recommend that you update the EdgeSwitch to the latest firmware.

Flashing White

Bootup in progress.

White

Ready for use, not connected to Ubiquiti Internet Service Provider (UISP). See “UISP Management”.

Blue

Ready for use, connected to UISP.

Steady Blue with Occasional Flashing

Ready for use, unable to connect to UISP, check connection to UISP server.

Quickly Flashing Blue

Used to locate a device in UISP.

Alternating
Blue/White

Firmware upgrade in progress.

RJ45 Speed/Link/Activity LED (Ports 1 - 24)

Off

No Link

Amber

Link Established at 10/100 Mbps

Flashing Indicates Activity

Green

Link Established at 1000 Mbps (1 Gbps)

Flashing Indicates Activity

SFP Speed/Link/Activity LED (Ports 1 - 2)

Off

No Link

Amber

Link Established at 100 Mbps

Flashing Indicates Activity

Green

Link Established at 1000 Mbps (1 Gbps)

Flashing Indicates Activity

RJ45 (Ports 1 - 24)

RJ45 ports support 10/100/1000 Ethernet connections.

SFP (Ports 1 - 2)

Hot-swappable SFP ports support 1 Gbps connections.

Reset Button

There are two methods to reset the EdgeSwitch to factory defaults:

Runtime Reset (Recommended)

The EdgeSwitch should be running after bootup is complete, and the System LED is white. Press and hold the Reset button. The EdgeSwitch will reboot, and the System LED becomes blue after three seconds. Continue to hold the Reset button for about 15 seconds until the System LED flashes blue for two seconds. This indicates that the EdgeSwitch has reset to its factory defaults.

Power-on Reset

  1. Disconnect power from the EdgeSwitch.
  2. While connecting power to the EdgeSwitch, hold the Reset button for about 15 seconds until the System LED flashes blue for two seconds. This indicates that the EdgeSwitch has reset to its factory defaults.

Console Port

RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45-to-DB9, serial console cable, also known as a rollover cable, to connect the Console port to your computer. Then configure the following settings as needed:

  • Baud rate 115200
  • Data bits 8
  • Parity NONE
  • Stop bits 1
  • Flow control NONE

DC Input

The 25VDC input can connect a redundant or stand-alone DC power source (not included) with minimum power: 25W, 25 to 16V, and 2.5 mm DC power inline connector.

Note: You can use the redundant DC power source as a hot spare; if the internal AC/DC power supply no longer provides power, then the EdgeSwitch will switch to the DC power source without interrupting its operation.

Power Port

Connect the included Power Cord to the Power port.

Hardware Installation

  1.  
  2. OR

Connecting Power

Connecting Ethernet

Connecting SFP

For information about compatible fiber SFP modules, visit: ubnt.link/SFP_DAC_Compatibility

Accessing the Configuration Interface

The EdgeSwitch is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, then it will use the default fallback IP address, 192.168.1.2. Proceed to the appropriate section, DHCP or “Fallback IP Address”:

DHCP

Use one of the following methods:

To log in, follow these steps:

  1. Launch your web browser. Type the appropriate IP address in the address field. Press enter (PC) or return (Mac).
  2. Enter ubnt in the Username and Password fields. Click Sign In.

The EdgeSwitch Configuration Interface will appear. Customize additional settings as needed. For more information, refer to the EdgeSwitch documentation, which is available at ui.com/download/edgemax

Fallback IP Address

  1. Ensure that your computer (or other host system) is connected to the EdgeSwitch.
  2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
  3. Launch your web browser. Type the appropriate IP address in the address field (192.168.1.2 is the default fallback IP address). Press enter (PC) or return (Mac).

  4. Enter ubnt in the Username and Password fields. Click Sign In.
  5. The EdgeSwitch Configuration Interface will appear. Go to Settings .
  6. Change the IP Address to a unique IP address. Click Apply.

Note: If you change the IP settings, then the session will be cut off, and you will need to reconnect to the EdgeSwitch using the new IP address.

Customize additional settings as needed. For more information, refer to the EdgeSwitch documentation, which is available at ui.com/download/edgemax

UISP Management

You can also manage your device using the Ubiquiti Internet Service Provider. UISP lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at uisp.ui.com

Specifications

ES-24-Lite

Dimensions

443 x 43 x 221 mm (17.44 x 1.69 x 8.70")

Weight

Rack-Mount Brackets Included 2.6 kg (5.7 lb)
Rack-Mount Brackets Excluded 2.51 kg (5.53 lb)

Total Non-Blocking Line Rate

26 Gbps

Max. AC Power Consumption

25W

Power Method

AC 100-240VAC/50-60 Hz, Universal Input
DC DC 25W, 25 to 16V, with 2.5 mm
DC Power Inline Connector

Power Supply

AC/DC, Internal, 25W DC

Rack-Mount

Yes, 1U High

ESD/EMP Protection

Air: ± 24 kV, Contact: ± 24 kV

Shock and Vibration

ETSI300-019-1.4 Standard

LEDs Per Port

RJ45 Data Ports Speed/Link/Activity
SFP Data Ports Speed/Link/Activity

Interfaces

Networking Interfaces (24) 10/100/1000 Mbps RJ45 Ethernet Ports
(2) 1 Gbps SFP Ethernet Ports
Management Interface (1) RJ45 Serial Port,
Ethernet In/Out Band

Operating Temperature

-5 to 40° C (23 to 104° F)

Operating Humidity

5 to 95% Noncondensing

Certifications

CE, FCC, IC