EdgePower 54V-150W Changelog
===========================================================================

1.10.0 Changelog / May 24, 2022:
====
- Don't disconnect charging when low voltage is detected
- PSU priority settings doesn't work after factory reset
- Filter Interfaces in SNMP
- improved support file

Checksums:
File    | EP.v1.10.0.989052.220328.1134.bin
MD5     | 3fc4a0d4f64633b1f91564bd79722cbe
SHA256  | fa0db6ed59c022c7036774fcc2ae65fa51c29a38a9196ccbd9f45b9bdd4b7d97


1.9.0 Changelog / May 28, 2021:
====
- fixed bug when Remote syslog settings doesn't work after factory reset 
- fixed incorrect timezone in UI after factory reset
- fixed bug when battery info is not reported if battery was disconnected for a while 
- fixed wrong battery detection if charger is enabled
- fixed data types in SNMP response
- NTP client is now enabled by default
- optimized power consumption during AC outage

1.8.0 Changelog / Oct 2, 2020:
====
- added ability to set SNMP Location and Contact in Settings page
- various WebUI fixes/improvments

1.8.0-beta1 Changelog / Sept 4, 2020:
====
- introducing new WebUi
- improved ping watchdog: allows set watchdog timeout from 1 minute to 1 hour

1.7.0 Changelog / May 15, 2020:
====
- Fixed bug where WebUI stops working if port is changed to 81
- Added detailed error message when automatic update check fails
- Introduced new SNMP battery fields: PsuBatteryChargeLevel,
  PsuBatteryTimeRemining, PsuBatteryReplaceIndicator, PsuBatteryLastReplaceDate
  (for more information see attached ubnt-mib)
- Optimized charging time for bad batteries
- Updates and fixes for better use with UNMS

1.6.0 Changelog / Jan 24, 2020:
====
- added Locate function in System > Device Maintenance tab. Allows to locate
  device by blinking LED.
- added warning when default password is used
- added support for reporting crashes. Option can be disabled in System > Device.
- Updated self-signed HTTPS certificate generation rules to match macOS v10.15 
  and iOS v13 requirements.
- fixed bug when Reset battery status doesn't reset currently running/planned calibration
- fixed Total power consumption when in some cases was counted inaccurate.
- fixed bug when User was immediately logged out when Web Server Session timeout field is set to 0
- fixed bug when default route was not set after reboot in some cases.
- various WebUI fixes
- various fixes/improvements for UNMS

1.5.0 Changelog / Sept 24, 2019:
====
- added automatic check of new firmware availability in UI
- fixed bug when hosname in UNMS key wasn't sometimes resolved by DNS
- battery settings are now hidden when no DC PSU inserted
- DC Out is now recovered from overloaded state when it was caused by
  a temporary outage of one PSU
- added support for UNMS Mobile apps.
- various fixes/improvements for UNMS

1.4.0 Changelog / Jun 19, 2019:
====
- Introduced new Dashboard
- Changed battery charger behavior - Battery charger is now enabled even if
  battery reach target voltage (in holding current state).
- Improved Low Voltage Disconnect function - DC Output was disconnected too
  earlier in some cases.
- Added Battery capacity and Installation date into Power tab
- Added support for Management VLAN setting
- Added support for Backup/Restore configuration
- Added Overloaded state - If actual power is higher than max power for 60s,
  disconnects outputs and after 10s tries to reconnect them again.
- Added support for reset total power consumption
- Fixed bug when Total power consumption was not reset during factory-reset
- Improved behavior when DHCP is used to get IP address and device is
  reconnected to other network (Device now tries to renew IP address)
- Improved UNMS support

1.3.1 Changelog / Nov 13, 2018:
====
- fixed power outage during reboot/upgrade
- fixed bug when PoE watchdog causes DC out to stay off

1.3.0 Changelog / Oct 3, 2018:
====
- added State to dashboard. Shows Online, PSU Offline, On battery,
  Battery low, Power off
- introduced new Power tab which will include all Power specific features
- replaced On/Off/Standby PSU properties with Priority options 
- added power-cycle for DC Output
- added ping watchdog: When EdgePower boots up, after a delay of 300 seconds,
  EdgePower starts checking selected IP address. If there is no response for
  3 times, DC output is power-cycled.
- added low voltage disconnect: When all batteries reach 11.8V,
  DC Output is turned off. This is indicated by Power off status.
- added timezone selection
- updated Discovery Responder
- enabled IPv6 Link local
- fixed bug when SSH authorized keys can not be imported
- minor fixes

1.2.0 Changelog / Jun 6, 2018:
====
- fixed bug when voltage was not correctly readed in some cases
- fixed WebUI dialog colors
- fixed WebUI dialog positions
- changed WebUI favicon
- minor fixes

1.2.0-beta.1 Changelog / Feb 1, 2018:
====
- added SNMP v1 support
- added UNMS support

1.1.0 Changelog / Aug 9, 2017
====
- enables DC/DC Module Support (Part #: EP-54V-150W-DC)
- backported discovery responder security fixes
- security updates to uclibc/openssl/lighttpd/php
- security fixes for WebUI CGI scripts
- default AC and DC module state handling, when configuration is not present
  while updating from v1.0.1 (Upgrading will not change the state of the PSU
  to off as it has in previous firmware upgrades.)